• This forum has 554 topics, 1,464 replies, and was last updated July 2, 2024 by Mike C.
    • VMware
    • serial output

      Hi, sorry about my poor english. I have a linux vm (RHEL7) over ESX. I want to enter kdb mode for debugging, I set the grub.conf file with kgdboc parameterlike this: console=tty0 kgdboc=kbd,ttyS0 when I cause a crash the system goes to kdb mode but I cant see it happens the console just freeze…  I […]

    • People: 2
      Replies: 1
    • January 11, 2017
    • IP renaming on Linux

      Hi all, I was recently installing ZVR5.0 After installation, I began the advised tests listed in the documentation, but I found an issue when renaming NIC’s IP. It happened when the VM had more than a NIC, and when during the setting of VPG only one of them was configured with the new one, leaving […]

    • People: 2
      Replies: 1
    • January 11, 2017
    • Can zerto cause VM performance issues?

      I am being told some of our third party engineers that all of our Virtual Machines are running slower than normal and the possible cause is due to the fact that I just recently installed Zerto. I am not able to replicate their tests and everything looks good on my end. Is it possible for […]

    • People: 2
      Replies: 1
    • January 9, 2017
    • Zerto and Netapp Snap Mirror

      IHAC that wishes to use Zerto to protect workloads however they also have a requirement to use Netapp Snapmirror to protect the same workloads and utilize snap mirror for long term backup. I am not a storage expert by any means. Is this a supportable workable solution? How would Zerto manage a failover when there […]

    • People: 2
      Replies: 2
    • December 28, 2016
    • vCloud 8 1 2

      Hello Now that vCloud Director 8 has been released, will Zerto be supporting is for service providers using it with Zerto to provide DRaaS?  If so, is running vCD8 with vSphere 6 underneath supported? Dave

    • People: 15
      Replies: 23
    • December 7, 2016
    • Test failover time period

      Hi I am new here, sorry if I post duplicate question. I want to ask if I have a VM with a 7 days protection by Zerto, and I trigger a test failover, is there any time limitation of stop the failover test? What happen if I test over 7 days, will it be impact […]

    • People: 2
      Replies: 1
    • November 28, 2016
    • MSCS Cluster – IP Change During Failover

      Hello During recovery of MSCS Cluster ( Active node/system), system failed over to DR site without any issue, but the cluster service did not come up. After reading through the documents, i see Zerto recommends preconfigure listeners on both the protected and recovery IP ranges, each node with a dedicated heartbeat NIC. is there any document […]

    • People: 2
      Replies: 1
    • November 16, 2016
    • VMware permissions not replicated

      We are protecting a VM that has some explicit VMware permissions applied to it tha allow the administrators of the VM access to it.  These permissions are not being replicated to the recovery site. When we test the failover, the owner of the VM no longer has access though vSphere. Has anyone else seen this […]

    • People: 2
      Replies: 1
    • November 2, 2016
    • vCloud vApp Networks

      Hello We are using Zerto 3.5 U7 to replicate vApps between two vCloud Director instances. We have a customer who is using vApp networks with firewall rules configured in their vApps.  In our current Zerto deployment, when those vApps are failed over the vApp Network is still there inside the recovered vApp but the NAT […]

    • People: 2
      Replies: 1
    • November 1, 2016
    • Workflows for vRealize Automation/Orchestration

      I’ll start out with saying that I’m new to vRealize Automation and Orchestration. I’d like to write workflows that call out to Zerto in order to create VPGs and migrate VMs.  Is there a plugin or similar available that has some prebuilt tasks?  Otherwise, where do I start on using the Zerto API.  I just […]

    • People: 2
      Replies: 2
    • October 31, 2016
    • Protection of turned-off machines

      Hello, is it really necessary for the VM to be running when adding it to a VPG? There are scenarios where you have virtual machine turned off, but want to protect it with Zerto (e. g. root certification authority, VM’s that are baselines for templates etc.). And it seems to me like unnecessary requirement to start this […]

    • People: 2
      Replies: 1
    • October 31, 2016
    • Can VRA be storage vmotioned?

      I have a datastore that I am trying to free up to discard and reuse for another purpose but I noticed there was a VRA on it. Can this be storage vmotioned off into another datastore (that does not contain an existing VRA) without issues? I did see the article of storage vmotion of multiple VRAs […]

    • People: 2
      Replies: 2
    • October 28, 2016
    • FailoverTest doesnt work in VM with Standard Port

      Hello all, I need to know if someone had the same problem like me. When I try to do a FailoverTest on a VM with standard port group, and the target network in a vDC is Distributed port group, it fails with this [ERROR], and VM is created in poweroff state. [ERROR] Task: Power Off […]

    • People: 2
      Replies: 1
    • October 25, 2016
1 2 3 … 33 34 35 36 37

The forum ‘VMware’ is closed to new topics and replies.