• This forum has 554 topics, 1,464 replies, and was last updated July 2, 2024 by Mike C.
    • VMware
    • Extend source vSphere virtual machine RDM disk

      Hi all, We have a VPG with one VM replicated to the secondary site. In source prod site this vSphere VM has 1 vmdk and 3 RDM physical mode disks. In replica site zerto creates 4 vmdk disks replica on VMFS datastore. Now I have to expand one of the production RDM disk and I […]

    • People: 2
      Replies: 1
    • October 25, 2016
    • Cisco Virtual Wireless Controller

      Has anyone Zerto’d a Cisco virtual wireless controller? I’m not sure why it wouldn’t work but was just curious. I don’t want to go down the route of setting up a BU controller if i can just take care of it with zerto.

    • People: 2
      Replies: 1
    • October 1, 2016
    • vCloud – Exclude VMs from vApp Replication

      Is there anyway to tell Zerto not to replicate certain VMs within a vApp in vCloud Director.  I see it is possible to configure certain disks as swap disks, which prevents changes being sent after initial sync, but this isn’t quite what I’m looking for.  We’ve got some vApps that contain VMs that we’re not […]

    • People: 2
      Replies: 1
    • October 1, 2016
    • how to use multiple DNS suffix

      hello all i’m erric from south korea i have question i want that use two DNS suffix how to use multiple DNS suffix <span class=”hps”>Please</span> <span class=”hps”>refer to the following</span> <span class=”hps”>files</span>  

    • People: 2
      Replies: 1
    • September 27, 2016
    • vCenter Migration & Zerto

      We are moving from a vCenter 5.1 linked-mode instance to two separate vCenter 6 instances. We also have Zerto 4.5 Update running in the 5.1 instance replicating 25 VMs. Is there a supported method to “reconfigure” Zerto once we move the vSphere hosts into the vCenter 6 instances?

    • People: 2
      Replies: 1
    • September 14, 2016
    • Set VM HW Version on failover VM

      Hello all, Is there a way to specify the target HW version of the failover VM?  Our source VMs are Hyper-V VMs so there isn’t a one-to-one copy so the target VM is setting it to the highest level, version 10.  We’d prefer to set the HW Version to 9.  Obviously this can be fixed […]

    • People: 4
      Replies: 4
    • August 23, 2016
    • vCenter issue scenarios

      Hi, our environment has separate Prod and a DR sites, with vCenter servers and ESXi hosts in both sites and ZVMs/VRAs in both sites. 1. If for whatever reason the DR VC server goes offline or is inaccessible, will this affect VPG replications or journal histories at all? 2. If for whatever reason. the prod […]

    • People: 2
      Replies: 4
    • July 18, 2016
    • Upgrade Zerto & VMware

      Hello All, I am facing a double upgrade dilemma and would like to see what folks’ thoughts are. We are currently running Zerto 3.5U7 on vSphere ESXi 5.5.  I have been holding off on upgrading as we wanted to do some significant testing first before rocking the boat with upgrades. So here’s my question(s) – […]

    • People: 3
      Replies: 3
    • June 21, 2016
    • VCD 8.10

      Hi there, Now that vCloud Director 8.10 is released: https://pubs.vmware.com/Release_Notes/en/vcd/8-10/rel_notes_vcloud_director_8-10.html Could you please advise when next incremental release of Zerto 4.5 with VCD 8.10 support will be available ? Regards, Mark

    • People: 4
      Replies: 5
    • June 15, 2016
    • Upgrading VMs – Zerto failback plan – use Pause?

      Hi there, We are using Zerto 3.5 u4 to replicate VMs between two sites. We are upgrading our VMs and need to come up with a failback plan using Zerto. The upgrade of the Virtual machines will take between 8 and 24 hours and we would like to be able to use Zerto to restore […]

    • People: 2
      Replies: 2
    • June 10, 2016
    • Linux VM Test Recovery Issue

      Hello Sir. I want to change IP address of VM when I perform the ‘Test failover’. Is there any pre-requirement or limit on this job ? (vmware tools already installed and running) I didn’t find any information on the Administrator Guide and other document. VMware tools in this VM was installed and all the status […]

    • People: 2
      Replies: 2
    • May 31, 2016
    • Upgrade ESXi hosts from 4.1 to 5.5

      Hello, we have a Zerto installation between our prod site (VMware Ent. 4.1) and a DR site (also VMware 4.1). Now we are planning to upgrade both infrastructure to version 5.5 of vmware, is it possible to perform the upgrade without losing actual protection? How ? Thanks in advance, Bruno

    • People: 4
      Replies: 4
    • May 4, 2016
    • Unable to view Zerto UI using vCenter plug-in

      Hi, I’ve changed the IP address of my DR ZVM server by following the KB 00000180 and it worked fine. However, I now can no longer access the Zerto UI via the vCenter plug-in. It says “page can’t be displayed, make sure the web address https://<old ZVM IP address>:9669 is correct”. Why is it not […]

    • People: 2
      Replies: 4
    • April 26, 2016
1 2 3 … 34 35 36 37

The forum ‘VMware’ is closed to new topics and replies.